닌텐도 DS Modding 인덱스

Hardmod

Hardmodding can easily damage your DSi. If you’re trying to unbrick your DSi, then you should try ntrboot first.

Hardmodding is when you physically solder the motherboard of the Nintendo DSi to an SD card adapter in order to be read on a computer. This is useful for restoring NAND backups, viewing NAND on your PC, etc…

Nintendo DS #

Original DS motherboard with touch-points labeled

닌텐도 DSi #

To hardmod a Nintendo DSi/DSi XL (LL) you will need: - Pencil tipped soldering iron - Very fine wire, 28AWG or smaller, preferably 30AWG+ - SD to microSD adapter - An SD card reader able to read eMMC chips running in single data-line mode. Here’s a known working one - Win32DiskImager and HxD if on Windows - A valid NAND backup of the DSi you are hardmodding - To be comfortable soldering to pads that are as small as 0.5mm in diameter

DSi side A pinouts #

DSi side A pinouts

DSi side B pinouts #

DSi side B pinouts

DSi XL side B pinouts #

DSi XL side B pinouts

  • You will need to solder the points on the motherboard to the microSD card adapter
    • CMD to pin 2
    • GND to pins 3 and 6
    • CLK to pin 5
    • DAT0 to pin 7

Soldered microSD adapter example #

microSD example

  • Insert the microSD card adapter into your computer
    • WARNING - Windows will ask you to format it: DO NOT format it - this might cause irrepairable damage

You will first need to remove the NOCASH footer from the backup you are flashing to the DSi. This can be done using the hiyaCFW helper.

  1. Download the version for the operating system you are using
  2. Run the script, selecting the NAND backup you wish to flash to your DSi
  3. Switch to NAND mode with the button to the left of the file path
  4. Click Start to create the NAND backup without the no$gba footer
  • Once the script completes, there should be a file with a long name ending in -no-footer.bin in the folder where your terminal is open
    • Use this file as the NAND image you flash onto the DSi

Flashing the NAND backup #

  1. Open Win32DiskImager
  2. Click the folder icon and browse to your desktop. In the text box, write NAND_0.bin. When selecting type, choose All types *.*
  3. Choose the device that is the DSi and click read
  4. Once it is done, click the folder icon, change the name to NAND_1.bin and read again
  5. Open HxD and drag both files into the editor. Go to the top bar, click “Analysis”, click “File compare” from the drop down menu, then click “Compare”.
  6. Choose to compare both files then click OK when done
    • If it says “The chosen files are identical.”, you are good to go to the next section
    • If it doesn’t say that, and both NANDs aren’t around 240 MB, dump NAND_1/NAND_0 again
  7. Open Win32DiskImager, click the folder icon and choose your existing NAND backup you created before
  8. Flash it with the Write button
  9. Unplug the SD card adapter and attempt to turn on the DSi
  1. Work out where the SD card is mounted
    • Linux:
      1. SD 카드 어댑터를 분리하세요
      2. Run lsblk in a terminal
      3. SD 카드 어댑터를 삽입하세요
      4. Run lsblk again
      5. This time a new device should appear
        • It may be called /dev/sdb, make sure you note down what it is called on your computer
    • macOS:
      1. SD 카드 어댑터를 분리하세요
      2. Run df in a terminal
      3. SD 카드 어댑터를 삽입하세요
      4. Run df again
      5. A new device should appear in the list
        • It may be called /dev/disk1s1, make sure you note down what it is called on your computer
  2. Dump the NAND
    • Run the following command in a terminal:
      • cat {device-name} > nand0.bin
      • Replace {device-name} with the SD card mount location
      • E.g cat /dev/sdb > nand0.bin
      • Then run cat {device-name} > nand1.bin
  3. Compare NAND dumps
    1. Run the following command:
      • Linux: md5sum nand0.bin nand1.bin
      • macOS: md5 -r nand0.bin nand1.bin
    2. Check that the hash generated matches each other
    3. If not, redump the NAND, adjusting the wiring if necessary
    4. Keep on redumping the NAND until the hashes are identical
  4. Flash NAND
    1. Locate the NAND backup you created before on the console
    2. Run the following command:
      • cat {existing-nand-backup} > {device-name}
      • Replace {existing-nand-backup} with the location and name of your old NAND backup
      • Replace {device-name} with the mount point of the SD card

At this point you may unplug the SD card adapter and attempt to turn on the DSi. If all went well, the DSi should have booted to the state it was when the backup was created!